“Printing” Tiny Batteries
Enlarge Photo
Image courtesy of Jennifer A. Lewis
Schematic showing nozzle of 3D printer depositing a layer of "ink" to form the battery anode (anode shown in purple, cathode shown in red). Image to the right shows microbattery in its casing.
In recent years engineers have invented many miniaturized devices, including medical implants, tiny cameras, and microphones that fit on a pair of glasses. But often the batteries that power them are as large or larger than the devices themselves, which defeats the purpose of building small.
Now a team of researchers—including collaborators from a DOE Energy Frontier Research Center (EFRC)—has shown that 3D printing can be used to print lithium-ion microbatteries the size of a grain of sand. The printed microbatteries could supply electricity to tiny devices in fields from medicine to communications, including many that have lingered on lab benches for lack of a battery small enough to fit the device, yet provide enough stored energy to power them.
To make the microbatteries, the team, based at Harvard University and the University of Illinois at Urbana-Champaign (UIUC), printed precisely interlaced stacks of tiny battery electrodes, each less than the width of a human hair.
"Not only did we demonstrate for the first time that we can 3D-print a battery; we demonstrated it in the most rigorous way," said Jennifer A. Lewis, senior author of the study and currently Hansjörg Wyss Professor of Biologically Inspired Engineering at the Harvard School of Engineering and Applied Sciences (SEAS) and a member of Harvard's Wyss Institute for Biologically Inspired Engineering.
Lewis is also a principal investigator in Light-Materials Interactions for Energy Conversion, an EFRC led by the California Institute of Technology involving several major universities as partners. Now at Harvard, Lewis led this project in her prior position as a professor at UIUC in collaboration with co-author Shen Dillon, a UIUC Assistant Professor of Materials Science and Engineering. The results have been published online in the journal Advanced Materials.
To get around this problem, manufacturers have traditionally deposited thin films of solid materials to build the electrodes. However, due to their ultra-thin design, these solid-state micro-batteries do not pack sufficient energy to power tomorrow's miniaturized devices.
“Not only did we demonstrate for the first time that we can 3D-print a battery; we demonstrated it in the most rigorous way.
” Jennifer A. Lewis
The scientists realized they could pack more energy if they could create stacks of tightly interlaced, ultrathin electrodes that were built out of plane. For this they turned to 3D printing. 3D printers follow instructions from three-dimensional computer drawings, depositing successive layers of material—inks—to build a physical object from the ground up, much like stacking a deck of cards one at a time. The technique is used in a range of fields, from producing crowns in dental labs to rapid prototyping of aerospace, automotive, and consumer goods. Lewis' group has greatly expanded the capabilities of 3D printing. They have designed a broad range of functional inks—inks with useful chemical and electrical properties. And they have used those inks with their custom-built 3D printers to create precise structures with the electronic, optical, mechanical, or biologically relevant properties they want.
To print 3D electrodes, Lewis' group first created and tested several specialized inks. Unlike the ink in an office inkjet printer, which comes out as droplets of liquid that wet the page, the inks developed for extrusion-based 3D printing must fulfill two difficult requirements. They must exit fine nozzles like toothpaste from a tube, and they must immediately harden into their final form.
In this case, the inks also had to function as electrochemically active materials to create working anodes and cathodes, and they had to harden into layers that are as narrow as those produced by thin-film manufacturing methods. To accomplish these goals, the researchers created an ink for the anode with nanoparticles of one lithium metal oxide compound, and an ink for the cathode from nanoparticles of another. The nanoparticles were immersed in a solution specially designed to assist in both solidifying the materials and creating bonds between the layers.
The printer deposited the inks onto the teeth of two gold "comb-like" current collectors, creating a tightly interlaced stack of anodes and cathodes. The resulting arrays were heated to 600°C to promote "sintering" or bonding among the nanoparticles.
Enlarge Photo
Photo courtesy of Jennifer A. Lewis
Scanning electron microscope image of microbattery array.
Then the researchers packaged the electrodes into a tiny container and filled it with an electrolyte solution to complete the battery.
Next, they measured how much energy could be packed into the tiny batteries, how much power they could deliver, and how long they held a charge. "The electrochemical performance is comparable to commercial batteries in terms of charge and discharge rate, cycle life and energy densities. We're just able to achieve this on a much smaller scale," Dillon said.
"Jennifer's innovative microbattery ink designs dramatically expand the practical uses of 3D printing, and simultaneously open up entirely new possibilities for miniaturization of all types of devices, both medical and non-medical. It's tremendously exciting," said Wyss Institute Founding Director Donald Ingber, who is also a Professor of Bioengineering at Harvard SEAS.
The work was supported by the National Science Foundation and by the DOE Office of Science through Light-Material Interactions in Energy Conversion EFRC. Lewis and Dillon collaborated with lead author Ke Sun, a graduate student in Materials Science and Engineering at the University of Illinois at Urbana-Champaign; Teng-Sing Wei, a graduate student at Harvard SEAS; Bok Yeop Ahn, a Senior Research Scientist at the Wyss Institute and SEAS; and Jung Yoon Seo, a visiting scientist in the Lewis group, from the Korea Advanced Institute of Science and Technology.
Dan Ferber, Harvard University, [email protected]
Article provided courtesy of the Wyss Institute for Biologically Inspired Engineering at Harvard and the Harvard School of Engineering and Applied Sciences.
Publication
Ke Sun, Teng-Sing Wei, Bok Yeop Ahn, Jung Yoon Seo, Shen J. Dillon, Jennifer A. Lewis, "3D Printing of Interdigitated Li-Ion Microbattery Architectures," Advanced Materials, published online June 17, 2013
Funding
National Science Foundation
DOE Office of Science
Related Links
Light-Materials Interactions in Energy Conversion EFRC
University of Illinois at Urbana Champaign, Department of Materials Science and Engineering
